A&D OP-11 Manual de instalación Pagina 51
- Pagina / 182
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
07/2011 2 Operating A&D DataManagement
2.4 Specifying the properties of the control components
© Siemens AG 2011 All Rights Reserved
SIMATIC A&D DataManagement Client - 07/2011
2-51
Note
With some CPUs, data or programs stored in the read only memory of the CPU
are also backed up. These blocks cannot be loaded back.
The following settings are offered:
• Use the online address of the source project:
If there is a pointer to an S7 source project in the properties of the S7
component, ADDM uses the access addresses stored in the S7 source
project for online access to the S7 CPU.
• Use the online address of the backup project:
If an S7 source project does not exist, then the access paths must be
defined in the backup project. This setting must be selected for this
purpose. The setting option is thus activated via the Online Address button.
Actuating the button opens Program Properties.
• Multibackup:
This option enables the user to store up to 99 memory dumps of the
component, also see subsection 2.4.1 and subsection 2.6.2.
Properties Program (online) - local
The settings for online access are made in this window. The Local setting defines a
direct access to the S7-CPU via the MPI address. The address must be known to
the user. If this information is lacking, the address can be found in ADDM with the
Display Accessible Nodes function. The address is entered in the "Connection to
destination station" under address.
- SIMATIC 1
- Content 3
- Content 07/2011 4
- 07/2011 Content 5
- 1 A&D DataManagement 7
- 1.1 Overview 8
- 1.1 Overview 9
- Supported software tools 10
- Miscellaneous 13
- 1.3.2 Backup concept 14
- ADDM single user version 15
- Hardware requirements 16
- Memory requirement 16
- Software requirements 17
- Update registry 17
- 1.4.4 Installing ADDM Agent 25
- 2.1 User log on 27
- Logging a new user on 28
- 2.1 User log on 29
- Creating a new project 30
- Imaging the plant structure 31
- Copying/insert a subproject 31
- Details of each component 32
- Editing a project 32
- Disable objects for editing 33
- Enable objekt 34
- 2.4.1 NCU component 36
- PROFIBUS option 38
- NCU adresses 39
- Tips for the NCU 39
- NCU versions 40
- Routing via agent option 41
- Multibackup option 41
- Only NC programs 42
- 2.4.3 S5 Component 45
- 2.4.4 S7 Component 47
- S7 source data 49
- S7-backup 49
- Properties of the S7 backup 50
- Query Subnet ID 53
- CP342-5 in V2 STEP7-project 56
- 2.4.7 Drive component 59
- Drive interfaces 60
- SimoComU/A 60
- DriveES 61
- 2.4.9 Serial component 66
- 2.4.10 Path component 68
- Assign user 69
- Backup 70
- 2.4.11 PCIN component 71
- Select data 72
- Creating a file list 72
- Setting COM parameters 73
- Necessary settings for HPU 74
- 2.4.12 Neutral component 76
- Load command 78
- Backup command 79
- Compare command 80
- Comparison executed by ADDM 81
- Comparing binary or ASCII 82
- Returnfile 82
- Routing neutral components 83
- 2.4.13 SINUMERIK components 84
- Addressing 85
- Contents of the backup 86
- Option, Routing via agent 86
- Save only in the reset state 86
- Max. no. of backups 86
- Connecting the computers 88
- Boot disk for use with ADDM 89
- Adapting Protocol.ini 90
- Adapting System.ini 91
- Load network driver locally 92
- Overview 93
- Comments 97
- Inserting variable text 99
- Language-dependent menus 100
- Adding a new language 101
- NETBEUI network protocol 102
- 2.5 HD component 103
- 2.5 HD component 104
- TCP/IP network protocol 106
- Data backup and loading 107
- Requirement 107
- Selecting a language 109
- Making bootmedium 110
- Start transfer 111
- 2.6 Transferring data 114
- 2.6 Transferring data 115
- MPI, OPI, PROFIBUS 119
- V24 COM1/2 ports 119
- LPT1 parallel port 120
- Interlink drivers 120
- Network connection 121
- USB connection 122
- PC card slot 122
- Infrared connection 123
- 2.7 Comparison functions 124
- 2.7 Comparison functions 125
- Results 126
- Results only for NC programs 126
- Data comparison 127
- Defining the exclusion list 128
- Go to 132
- Select comparison source 133
- 2.7.5 Comparing the S7 CPU 134
- Defining the inclusion list 135
- Comparison per job 136
- 2.7.6 Comparing CPs 137
- 2.7.7 Comparing OPs 138
- 2.8 SIMATIC S7 functions 140
- 2.8 SIMATIC S7 functions 141
- 2.9.7 NC-Files to the PCU 146
- 2.10 Standard functions 148
- HMI DOS settings 149
- OP settings 150
- HD settings 150
- PCIN settings 151
- Multibackup settings 151
- Backup and Archive 152
- Neutral Component 152
- 2.10 Standard functions 153
- NCU component 154
- 2.10.2 Moving menu bars 155
- 2.10.5 Printing 158
- 2.10.6 Online-Hilfe 158
- 2.10.7 The About window 159
- 2.10.8 Changing icon files 159
- Ethernet (TCP/IP) 160
- Software 161
- 2.11 User management 162
- 2.11.1 Creating a new group 163
- 2.11.2 Creating a new user 164
- 2.12 Archive functions 165
- 2.12.3 Archiving 167
- 2.12.4 Dearchiving 168
- 2.12.6 Comparing archives 169
- 2.12.8 Displaying versions 170
- 2.12.9 Backup and Archive 171
- 2.13 Job server 173
- 2.13.3 Create Job 174
- 2.13 Job server 175
- 2.13.4 Confirm Job 176
- 2.14 Notes and tips 177
- A Appendix 179
- A Appendix 07/2011 180
- 07/2011 A Appendix 181
Relacionado con productos y manuales para De medición, control y control A&D OP-11
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.100 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales